SC1000 Probe Module, 4 Sensor Connectors, 4 mA Output, 100-240 VAC, without power cord

SC1000 Probe Module, 4 Sensor Connectors, 4 mA Output, 100-240 VAC, without power cord
Productnr.: LXV400.99.00122
Prijs per eenheid Neem contact op
Wordt binnen 1 week verzonden

Flexible: individually configurable

There’s no complicated wiring or set up procedures with the
sc1000 controller. Just plug the sensor into a Probe Module
and it’s ready for use. No special ordering or software
configuration is needed.

Future-safe: always expandable

Any Hach digital sensor can be plugged into the sc1000
Probe Module in any combination. Available parameters
include—but are not limited to—dissolved oxygen, pH, ORP,
conductivity, turbidity, suspended solids, nitrate, chlorine, ammonia, phosphate, etc.

Intuitive operation: display with touchscreen

Communication and relay options for the sc1000 controller
can be configured to suit any situation. Available
configurations for a single Probe Module include:
• up to 4 relay contacts for alarm and control functions,
• up to 12 analog outputs for measured values,
• up to 12 analog or digital inputs from non-digital sensors
(i.e., flow or pressure sensors),
• up to 8 digital inputs from digital sensors,
• select from multiple network card options such as
MODBUS®, PROFIBUS DP®, and more.

Many additional versions available on request

Use the sc1000 controller for hassle-free communications.
Advanced communication features include:
Modbus TCP/IP—The sc1000 controller features
state-of-the art Modbus TCP/IP communications
protocol for seamless integration into a network of
devices that support TCP/IP sockets. Use a
standard Ethernet cable or connect wirelessly using
GSM/GPRS to communicate with your SCADA,
PLC or your organization’s network.

Expandable and Upgradeable

The Hach sc1000 Controller can adapt to your needs.
Change probes without changing the controller. With a
single Display Module, additional Probe Modules can be
added or removed depending on operational needs. Fully
upgradeable software ensures that this system will not be
obsolete. Hach service plans are available.

Wat zit er in de doos

SC1000 Probe Module with installed cards (as requested), Basic User Manual

Specificaties

Afmetingen (H x B x D): 150 mm x 315 mm x 250 mm
Alarm: Laag alarmpunt, neutrale zone laag alarmpunt, hoog alarmpunt, neutrale zone hoog alarmpunt, vertraging uitgeschakeld en vertraging ingeschakeld
Analoge uitgang signaal: Functionele instelling: PID, high/low phasing, setpoint, deadband, overfeed timer, off delay, on delay
Analog Output: One 4-20 mA Output Module
Analogue inputs: No Input Module
Beschermingsklasse: IP65
Bevestingsstijl: Oppervlak, paneel en buizen (horizontaal en verticaal) met optionele zonnekap
Certificering: Europese certificeringen:
CE per 73/23/EEC en 89/336/EEC
TUV-GS tot EN 61010-1
EN 61326 Amd's 1 en 2
Communicatie: Modbus (RS485): geavanceerde communicatie/netwerken met PLC- of SCADA-systeem direct vanuit de analyzer
Profibus DP/V1 (gecertificeerd)
GSM/GPRS Quad-band mobiele module (goedgekeurd door FCC en IC, alleen EU en VS)
Ethernetservicepoort, RJ45, 10 MB/s
Communicatie Mogelijkheden: Geen
Conduit for Relay Connection: Nee
Display: Backlit tft-glas/glas hoogresistent VGA-kleurentouchscreen van 14 cm met 320 x 240 pixels
Display : 11,4 x 8,6 cm
Garantie: 24 maanden
Gewicht : Ca. 6,5 kg (afhankelijk van configuratie)
Ingangen: Maximaal 12 analoge 0-20 mA, maximale impedantie 500 ohm per sensormodule. Aanvullende inputs beschikbaar met aanvullende sensormodules.
Materiaal: ABS (display module) and metal (probe module) enclosure with corrosion resistant finish
Omgevingstemperatuur: -20 - 55 °C / 0 - 95% relative humidity, non-condensing
Opslag condities: -20 - 70 °C / 0 - 95% relatieve luchtvochtigheid, niet-condenserend
Prognosys: Nee
Relais: No Relay
RTC Module: Nee
Sensors: 4
Stroom opties: 100-240V, geen voedingskabel, met buis
Uitgang: Maximaal 12 analoge 0/4-20 mA, maximale impedantie 500 ohm per sensormodule.
Aanvullende analoge outputs beschikbaar met aanvullende sernsormodules. Optionele digitale communicatie via Modbus (RS485) en Profibus DP/V1.
  Up to 12 analog 0/4-20 mA, maximum impedance 500 Ohms per probe module.

Additional analog outputs with additional probe modules. Optional digital communcations via Modbus® (RS485) and Profibus® DP/V1.
Wat zit er in de doos: SC1000 Probe Module with installed cards (as requested), Basic User Manual